The Cabling Conundrum – Cable tagging

Very often we come across installations where OFC cabling is completed but not properly tagged. This creates problems after splicing with either wrong cables in the right rack/panel or the right cable in the wrong rack/panel.  How do we get over this problem –

Here are a few tips:

a. Using Labels:

Adopt a simple cable tagging code from which you can figure out the origin of the cable say  three 6F Single mode cables laid between the Main Control Room(MCR) and Remote Panel/s -1, 2, 3(RP1, 2, 3).

At the MCR, just tag  the cable RP1_SM_6F, RP2_SM_6F & RP3_SM-6F

At the Remote Panel/s just tag the cable MCR_SM_6F_1, MCR_SM_6F_2 & MCR_SM_6F_3 respectively at the three remote panels

b. Using colours:

In the above example assign colours to each of the Remote Panels say Red, Yellow, Blue for RP1, RP2 & RP3. Tape the cable ends Red, Yellow & Blue using colour insulation/duct tape.

Just deciding on any of the above tagging methods based on the number of cables to ensure easy identification will save lots of time & effort in resolving communication issues without having to reroute cables and redo splicing.

Know more about our products & services, please visit http://www.yaminiengineers.com.

 

 

Single mode to Multimode fiber converters

Have you come across a situation where you are stuck with singlemode cable and multimode converters and you have to establish fast ethernet communication ?

You can’t relay multimode cable or replace the multimode converters supplied with singlemode converters – What do you do ?

Well, you can install singlemode to multimode converters. These are active devices with two SFP slots that take a MM 100FX SFP on  one  and a SM 100FX SFP on the other. Hook up the LIU end with a SM patchcord to the singlemode SFP and the MM SFP to the MM media converter with a Multimode patchcord and power on the converters…Your link should be up and running !!

A smart way to get around cable and converter mismatches. Want to know more about our products and services ? Please visit http://www.yaminiengineers.com. We are all about passive and active fiber optic products.

 

Pigtails, Adapters & Patch cords

typical_connection_liu_pt_ad_pc_sw

Pigtails are short pieces of 0.9mm buffered fibre connectorised at one end and the other end free to be spliced with the optical fibre cable. The No. of pigtails is generally equal to no of fibres in the cable unless some fibres in the cable are left unspliced. It is a good practice to splice all the fibres with pigtails and have all fibres ready for use.You will find the pigtails inside the LIU as you can see from the pictures in the attached file.

Adapters aka Mating sleeves aka couplers are mating points of the pigtail and patchcord. The pigtail is plugged into the adapter at the end inside the LIU and the patchcord is plugged into the end outside the LIU.

Patch cords are flexible fibre optic cable assemblies that facilitate connection between the LIU and the active equipment viz. Ethernet switches and media converters. Patch cords can be simplex or duplex. Simplex means one fibre and duplex means two fibres. Generally fibre optic communication is full duplex meaning a dedicated fibre for the transmit signal and a dedicated fibre for the the receive signal. Accordingly the patch cords are more often duplex than simplex particularly for data communications.

Know more about this please visit http://www.yaminiengineers.com. We are all about passive and active fiber optic products.

 

Splice closures

Splice closures (aka Joint closures) are weatherproof enclosures used to splice 2 or more optical fibre cables. They come in either rectangular or cylindrical construction. The splice closures have  2 -4 cable entry ports to bring the the cables in, splice trays for joining the individual fibres of the cables to each other and properly routing the same. Upon splicing the cable entry ports are sealed with heat shrinkable sleeves. There is also a mechanical design which enables re-opening of the closure if required. The closures are made out of light weight plastic. Once properly sealed the closure is water proof and air tight. Hardware used in the closure is rust proof. The closure generally conforms to IP-68 and suitable for underground direct burial, aerial or duct burial applications.

Know more about this please visit http://www.yaminiengineers.com. We are all about passive and active fiber optic products.